Browse all practice questions for the Omaha Journeyman Practice Test. Search by topic, open any question and review its full explanation, then test yourself in the practice quiz.

Omaha Journeyman Practice Test course image
More practice questions

These questions are part of the practice quiz. Start practicing

  • Cleanouts in waste pipes 2" and smaller shall have at least how many inches of horizontal space in front of the cleanout?
  • What is the minimum height for a bathroom ceiling?
  • Under what condition are two-way clean outs not required on building storm drains?
  • Which is the maximum number of water closets allowed on a 3 inch stack in a single family dwelling?
  • Where must the outlet pipe in a grease interceptor originate?
  • What material should be used to protect piping passing through walls?
  • What is the fixture unit rating for a typical residential bathroom sink?
  • To determine minimum roof drain square feet, what must be added to the roof area of a roof measuring 40' by 20' with a vertical wall on one side measuring 4' by 40'?
  • What is the minimum required depth of a floor sink?
  • What is the common unit for measuring plumbing fixture loading?
  • What is required for overflow drains where roof drains are installed?
  • What is the minimum waste opening size required on a laundry sink?
  • What is the minimum size service opening for a whirlpool tub?
  • What is the maximum number of water closets that would be allowed on a 4" building drain with 1/4 inch slope?
  • What type of fitting is required at the base of a vertical stack to allow for cleaning?
  • Which of the following materials is commonly used for laying drainage pipes?
  • Which of the following criteria does not apply to a 4-inch running trap?
  • What type of water closet installation is permissible in a medical specimen collection room?
  • What is the minimum distance allowed between two water closets, measured center to center?
  • Type K or L soft copper is permissible when placed in which orientation in a partition on remodel only?
  • When a back water valve is installed in a subsoil drain system, it is required to be in a minimum ______________ inch diameter manhole.
  • What is the minimum required clearance in front of a water closet?
  • What is the primary material recommended for building drains in commercial installations?
  • Is the installation of a pressure vacuum breaker inside a building allowed?
  • What is the minimum waste pipe size required for a shower?
  • Which type of interceptor requires the greatest minimum trap seal?
  • Subsoil drainage systems cannot be discharged into what?
  • Under what condition may a water closet be installed without a lavatory in the same room?
  • What gauge brass must all tubing used for tail pieces in commercial installations be?
  • A handicapped accessible water closet shall be _________ inches from the wall to the center of the water closet.
  • What schedule pipe is galvanized water pipe required to be?
  • What is the minimum diameter for a commercial garage drain?
  • What is the minimum vent pipe size from a sump or receiving tank for a sewage pump system?
  • What is the summation of two standard 90-degree turns in a drain line's total effective length?
  • Which pipe material is typically used for drainage systems?
  • What is the function of a thermostatic mixing valve?
  • How long must you wait before retesting if you do not pass a plumbing-related exam?
  • What is the maximum spout height of a handicapped accessible drinking fountain?
  • How much space must be allowed for minimum floor turn around space in an ADA restroom?
  • A shampoo sink in a beauty shop has a fixture unit rating of ___________.
  • The combined area of the openings through a floor drain cover must be equal to or greater than what?
  • How often shall all grease interceptors be pumped?
  • When measuring the maximum height of a testable backflow device, to what should the measurement be taken?
  • What is the minimum required clearance in front of a floor urinal?
  • To ensure accessibility, what type of installation is preferred for dielectric unions?
  • What is the minimum clear floor space required in front of a shower opening?
  • When installing water supply lines, what is a common requirement for backflow prevention?
  • On a 4-inch mop sink waste that is extended 38 feet from its connection on a horizontal main, what is the minimum size vent required?
  • Which type of trap is legal for use in plumbing installations?
  • What is the minimum distance above the flood level of a fixture required for an approved air gap?
  • The purpose of an interceptor is to?
  • When connecting a subsoil drain system by gravity to a storm sewer, what must be used?
  • When can you use a PVC "waste and overflow" on a bathtub in an apartment building?
  • For piping larger than two inches in diameter, how many inches of horizontal service space shall be provided in front of the cleanout?
  • Spills during the maintenance of grease interceptors must be reported within how many hours?
  • What is the required distance of a cleanout from a building foundation?
  • What is the function of a trap seal in plumbing?
  • What is the primary purpose of a grease interceptor in a commercial kitchen?
  • What is the function of a grease interceptor?
  • The relief vent in a multi-story building shall be what size?
  • When installing plastic pipe underground, what is the maximum distance between supports that secure the pipe to the bottom of the trench?
  • Handicapped accessible water closets height is measured from the finished floor to the top of the what?
  • What is the minimum required slope for a horizontal vent line?
  • What is the minimum allowable length of a non-handicapped accessible stall or compartment for a water closet?
  • Which material is typically used for a lead and oakum joint?
  • Construction specifications for inspection manholes installed for grease interceptors are the responsibility of?
  • If a vent stack terminates 4 feet from a ventilation grill, what must be done?
  • What is the minimum required clear space in front of a lavatory?
  • The chambers of a grease interceptor shall be accessible from the surface by means of a separate _______________ inch opening.
  • The maximum height of a flush valve handle for a handicapped accessible water closet shall be how many inches from a finished floor?
  • What is the mandated distance between any two lavatories in a series installation?
  • When can a circulation pump for a whirlpool tub be installed below the fixture trap?
  • The minimum space allowed between the edge of a lavatory and a wall is?
  • What is the minimum number of employees that require adequate toilet facilities on construction sites?
  • Which of the following back flow preventers cannot be used in a continuous pressure situation?
  • What is the minimum thickness of a closet floor flange?
  • Which of these fixtures requires an overflow?
  • A service sink with a three inch trap standard would have a fixture unit rating of?
  • The minimum liquid depth of a type III interceptor is _______ inches.
  • Wash fountains have a fixture unit rating of ________.
  • What is the minimum discharge pipe size required from a sump or receiving tank for sewage pump systems?
  • Chemical and soap dispensing equipment must be connected to which type of supply?
  • Which type of trap is typically used in kitchen sinks?
  • What is the minimum required waste pipe size for a trench drain that is 8' long?
  • In what position can a no-hub reducing coupling be used?
  • What type of materials are trench drains made of in corrosive conditions?
  • What is the minimum clear space required for cleaning an intercepting trap?
  • When a lead flashing for a vent stack is used, what is the minimum weight per square foot of the lead?
  • For what purpose may non-potable water be used?
  • In plumbing systems, cleanouts are generally installed to facilitate what process?
  • What is the minimum height of a trap arm vertical from the trap outlet?
  • The inlet pipe of a grease interceptor shall extend to how many inches below the liquid level?
  • What is the maximum number of clothes washers allowed on a three-inch stack?
  • A sump pump located in an elevator pit shall discharge as what?
  • What is the minimum clear floor space required in front of the test parts of a backflow assembly?
  • Cross linked polyethylene (PEX) pipe may be used for _________ water only?
  • What is the correct mounting height for a Reduced Pressure Zone (RPZ) device?
  • A commercial disposal with a three-inch trap has a fixture rating of what?
  • What is the minimum waste pipe size for a residential food waste grinder?
  • What is the minimum capacity of a grease interceptor?
  • When is a business required to allow the public access to the restrooms?
  • The rim or counter surface shall be no higher than ________ inches above the finished floor on a handicapped accessible lavatory.
  • What is the minimum size of a floor drain receiving the discharge from a 2 inch RPZ?
  • What is the minimum trap seal required on a Type 1 interceptor?
  • What is the minimum allowed slope of the bottom of a trench drain?
  • If a large wash basin for hand washing is 80 inches around, it may be considered as equal to how many lavatories?
  • What kind of trap should not be installed in a drainage system?
  • A relief vent is required when there are how many or more branch intervals?
  • A handicapped accessible lavatory shall have what minimum clear floor space?
  • Non-potable water lines shall be labeled with __________ labels and ________ letters.
  • What is the minimum combined area "in square feet" of a mopsink?
  • What is the minimum access opening required for a backwater valve installed inside a building and less than 24 inches deep?
  • On building storm drains requiring a manhole, the manhole shall be what distance or less from the building?
  • All residential garage drains shall be classified as which type of drains?
  • What is the minimum size waistline for a floor sink?
  • Which type of material is never acceptable for use in underground waste and vent systems?
  • What is the minimum required depth for a mop sink?
  • What should be done with spills that occur during pumping of grease interceptors?
  • The purpose of plumbing traps is to:
  • Which term refers to the maximum allowed flow of a fixture based on its nominal size?
  • What is the minimum depth of lead in a joint when making a lead and oakum joint on bell and spigot pipe?
  • What is the minimum allowed distance from the floor to the center of the tee serving a clothes washer?
  • The highest fixture connected to a waste or soil stack that does not require a re-vent is referred to as what?
  • What is the maximum number of back-to-back clothes washers allowed on a four-inch horizontal drain?
  • What is the minimum vent size allowed for a fixture?
  • What is the primary responsibility of the plumber concerning water supply?
  • What is the minimum depth of a trap seal in inches?
  • What type of drainage system is required for a facility with multiple food service areas?
  • A reduced pressure principle backflow might discharge how many times the rated flow of the device?
  • When can a drinking fountain be installed with an indirect waste?
  • A pedestal urinal has a fixture unit rating of how many units?
  • Shower rooms having more than two shower stalls shall provide which of the following near the stalls?
  • What is the minimum required distance from the center of a water closet to the center of a urinal?
  • Grease interceptors cannot be made of which type of material?
  • Under which condition are wells not required to be protected by man RPZ?
  • When may a water heater be connected using a flexible connector?
  • How should the vent from a pneumatic ejector system be configured?
  • Which is the primary purpose of a trap in plumbing systems?
  • What type of valve must be installed to protect quick closing valves on water lines?
  • The distance between clean outs on a 2" horizontal waste line shall not exceed how many feet?
  • What type of water supply is recommended for chemical dispensing?
  • For clothes washers, what unit rating applies when there are individual units in a group of three or more?
  • What is the maximum support distance for underground plastic pipes?
  • A two-way cleanout is not required if the building drain is extended to a manhole that is how many feet or less from the building?
  • When installing plastic waste piping below grade, what is the minimum clearance required around the entire outer circumference of the pipe or fitting when penetrating concrete?
  • Slip joint compression type waste line connections shall be accessible for what purpose?
  • What is the minimum trap size required for a bidet?
  • When is a vertical rainwater leader installed inside the building not required to have a cleanout?
  • What is the primary function of a grease trap in plumbing systems?
  • What is the minimum clear floor space required in front of a handicapped accessible lavatory?
  • According to plumbing codes, how far can a vent be from the trap it serves?
  • What is the maximum clear floor space for a handicapped accessible wall or post water fountain cooler?
  • Which of the following cannot be used for backflow protection in a high hazard?
  • Joints between no-hub cast iron and any other approved material shall be made with a ________ transition coupling.
  • What is the minimum trap seal for a shower?
  • A shower room having 8 multiple shower valves shall be served by a minimum __________ inch drain.
  • To install, maintain, and repair testable backflow assemblies, a journeyman is required to be certified through programs approved by which institution?
  • All below grade water supplies, one inch and smaller in size, shall be made of what type of copper?
  • Pressure building sewers shall schedule which PVC pipe and fittings?
  • When is it permissible to connect a storm drain to a sanitary sewer?
  • Which body of water is typically not allowed to directly connect to a sewer system?
  • What would be the fixture rating for a bar sink with a disposal in a private residence?
  • The maximum rim height of a handicapped accessible urinal is __________ inches from the floor.
  • For a multi-shower setup, what is the necessary drain size for each 10 shower heads?
  • What is the minimum inside diameter for a manhole used for a cleanout with more than one inlet?
  • What type of valve is commonly used for shutting off water supply in residential plumbing?
  • What is the primary purpose of having a floor drain in a shower room?
  • What is the correct size of a floor drain for a bathroom area?
  • What is the minimum allowed thickness of the concrete installed to encase a trench drain?
  • When a scupper is used as an overflow, drains must be?
  • All Durham soil and waste systems must be of which drainage type?
  • What grade of brass should be used for tail pieces in commercial plumbing installations?
  • What is the correct position for a vent stack when installed for a plumbing fixture?
  • If two lavatories are installed back to back in a wall, what is true about their waste connections?
  • When may grease traps be installed?
  • Which of these steps would not be an acceptable solution to prevent cross connection from threaded faucets?
  • How many fixtures can be discharged onto a stack above a stack vented water closet?
  • A transition coupling may be used to ___________.
  • When using lead as a flashing on a roof drain, how far must the flashing extend beyond the outer circumference of the stone guard clamping ring?
  • If a type I interceptor is 18 feet from the point of connection to the building drain, what is the minimum size vent required?
  • Which type of valve would be inappropriate to use for anti-scald devices?
  • What is the minimum vertical service space required in clean outs regardless of pipe size?
  • What is the minimum rated flow capacity for a grease trap?
  • On a horizontal branch, what is the maximum distance from the fixture opening that a vent can be connected?
  • What is the minimum diameter for a floor sink's waistline?
  • If two 45-degree ell fittings are spaced how many feet apart, a cleanout is not required?
  • Which of the following plumbing fixtures requires the least water flow capacity?
  • What are the required dimensions for clear floor space on a handicapped accessible urinal?
  • What is the purpose of a back flow valve in plumbing systems?
  • What is the maximum height of the flush valve handle for a handicapped accessible water closet?
  • Which of the following materials may not be used to secure a closet flange to the floor?
  • What is the minimum clearance of a handicapped accessible lavatory from finish floor to bottom of apron?
  • What is the minimum diameter required for a removable shower strainer?
  • Trench drains used in chemical or corrosive conditions shall be made of ___________________.
  • What is the maximum vertical rise allowed for a branch soil line extended to the first floor for specific fixtures?
  • A water closet in a retail establishment has a fixture unit rating of how many?
  • What is the purpose of the plumbing vent system?
  • On a horizontal waste branch ________ feet or less in length, the fixture outlet may be termed a cleanout.
  • A back flow valve installed in a manhole more than 2 feet deep requires the diameter of the manhole to be at least how many inches?
  • Which of the following fixtures requires an independent isolation valve?
  • Water leaking from a properly installed atmospheric vacuum breaker may be caused by what issue?
  • Clothes washers in a group of three or more have an individual fixture unit rating of?
  • What is required when a bypass is installed around a RPZ?
  • What is the appropriate vent size for a bathroom sink drain?
  • A pressure vacuum breaker shall be installed a minimum of _________ inches above the highest point of usage.
  • What is the maximum net square footage allowed for a unisex restroom in a retail business?
  • How much clear space is required above a water closet?
  • In plumbing, what does RPZ stand for?
  • Which fixture is allowed in a new commercial kitchen according to the provided regulations?
  • A partition is required between _________?
  • Which of the following describes how a grease trap must operate?
  • What is an essential requirement for slip joint waste line connections?
  • Which fixture's final waste connection cannot be made using a compression gasket?
  • A sump that receives the waste from a single floor drain does not require what?
  • How many inches from the side of a urinal to any wall or partition is the minimum?
  • What is the maximum depth of a vault housing a water meter?
  • What can the discharge point from a subsoil drain do?
  • What material is used for dishwasher waste pumped "below the floor"?
  • Which method is appropriate to protect a potable water supply servicing a tank with a toxic solution?
  • What is an owner's responsibility regarding grease interceptors?
  • What is the minimum width requirement for a doorway in a residential building?
  • The relief vent in a battery venting situation shall be no smaller than ______________.
  • What is the primary purpose of a grease interceptor?
  • The seal of every fitting trap in a plumbing system shall be protected by a ________.
  • What is the required supply line for ice machines and coffee dispensers from a minimum 1/2" rigid water pipe?
  • What is the minimum height for a mop sink faucet to be mounted above the finished floor?
  • What is the minimum size for a main cleanout in a residential plumbing system?
  • The heel inlet of a heel inlet one quarter bend shall be installed only in the _________ position.
  • What is the maximum height from finished floor to rim for a handicapped accessible lavatory?
  • What is the maximum slope of a battery vented soil or waste branch?
  • How high above the flood rim of a fixture must a vent be extended vertically before it can be run horizontally?
  • What must be considered when determining drain sizes for a commercial kitchen?
  • A pan shall be provided for all floor drains when it is installed where?
  • The adequate ventilation of plumbing systems is necessary to prevent which of the following?
  • The fixture load of a 4 inch branch interval is based on how many per inch per foot fall?
  • What is the function of a vent stack in a plumbing system?
  • What is the minimum size plastic soil or waste pipe that may be installed underground?
  • What is the maximum allowed distance from the finished floor to the center of the tee serving a clothes washer?
  • What is the maximum height from the rim of a wall-mounted urinal to the floor?
  • Cleanouts are required on building sewers at intervals not to exceed how many feet?
  • What is the minimum size concrete pad for a two-way cleanout on a building sewer?
  • Which of the following shall not be installed in a new commercial kitchen?
  • A manhole is required when installing a rainwater leader on _______ inch or larger pipe.
  • What is the minimum clearance required for a cleanout in a horizontal waste pipe?
  • What is the purpose of a vent in a plumbing system?
  • Where shall drinking fountains or water coolers not be installed?
  • What is the earliest time after installation that a new water meter can be examined for accuracy?
  • What is the maximum vent size allowed for two water closets installed back to back?
  • When passing through a wood stud, what thickness of steel plate must PVC be protected by?
  • At what height above finished floor should a cleanout be installed above a water closet?
  • Which of the following is not used as an anti-scald device?
  • Flexible water supplies for plumbing fixtures may exceed the maximum ________________ length limitation if necessary for structural and or mobility reasons.
  • For a building drainage system, which material is most commonly used for drainage pipes?
  • A potable well __________ cross connected with the water supply from MUD if used as an emergency backup to the water supply for a building.
  • What is the minimum size measurement inside of a shower stall?
  • Which fixture is not permissible for wet venting a water closet?
  • What type of cleanout is often used in building sewers for effective maintenance?
  • What is the minimum width of a stall for a non-handicapped water closet?
  • Flow control devices for grease traps shall be installed on which of the following?
  • When a stack is extended above the first floor to receive the discharge of plumbing fixtures, the stack vent must be what?
  • A single waste fixture unit is equal to how many gallons per minute?
  • If a 2 inch area drain is connected to a properly vented sanitary building drain, what is the maximum distance allowed between the building and the trap before a vent is required?
  • What is not a requirement for a flushometer?
  • A water closet in an establishment serving liquor is rated as what number of waste units?
  • When a fixture has an overflow, the waste must be arranged so that standing water in the fixture ___________ in the overflow when the stopper is closed.
  • What is the maximum number of bath tubs allowed on a 3" building drain?
  • What is the maximum number of side by side clothes washers permitted on a 4 inch horizontal waste?
  • What is the minimum size for a residential garage drain?
  • All commercial garage drains shall connect to a ________ interceptor.
  • What is the maximum allowable length of a 2" horizontal waste arm from the combination wye and 1/8 bend fitting to the fixture connection before a revent is required?
  • In what position should a water meter be installed?
  • How is the waste system for a grease interceptor vented?
  • What is the maximum height that a washing machine drain may be installed above finished floor?
  • What is the maximum discharge temperature allowed for a Type IV interceptor?
  • What is the minimum waste pipe size for a type 1 interceptor?
  • A residential dishwasher not connected to a kitchen sink has a fixture unit rating of ___________.
  • What is the maximum amount of fixtures allowed on a single battery vent?
  • What is the required clearance in front of a pedestal urinal?
  • The distance between clean outs on horizontal waste lines larger than 2" shall not exceed?
  • What is the maximum depth in inches for the trap seal of a 3" p-trap?
  • How many fixtures may be installed or connected to a single grease trap?
  • When installing a horizontal soil line, a clothes washer branch connection may not be connected closer than how many feet downstream from a water closet opening?
  • What should be done to prevent backflow in a plumbing system?
  • What is the minimum clearance for knee space at a cantilever type water fountain from the finish floor?
  • On new construction, a drain is required to be located no more than how many feet from a RPZ assembly?
  • What is the minimum width of the clear space for a handicapped accessible water fountain or cooler?
  • What should be the distance from a sewer connection to the drinking water supply?
  • What is the critical criteria for the installation of a running trap?
  • How should waste from a commercial type dishwasher be piped?
  • What is the typical slope required for a horizontal drain line?
  • How many 4 inch vent stacks would be required for a 6 inch building drain?
  • The valve control area for a handicapped accessible shower is from what height to what height above the finish floor?
  • Dielectric unions may be used if installed in which area?
  • All commercial garage drains shall be a minimum size of how many inches?
  • What is the minimum slope required for the floor to the floor drain in a public restroom that sells food or drinks?
  • What is the minimum number of bands required for no-hub couplings installed underground?
  • The waste pipe from a garbage can washer shall drain to which of the following?
  • Which type of floor urinal does not have an integral trap?
  • A shower waste shall run independent of other fixtures directly to a _______ inch or larger waste.
  • Any potable water supply going to a pressure sewer waste shall be through what?
  • Under what conditions are enzymatic grease interceptors allowed?
  • The minimum knee clearance under a sink for ADA is ______ inches above finish floor.
  • For a shower room with multiple shower heads, what is the minimum drain size required per 10 valves or heads?
  • How far can a pump and motor on a whirlpool tub be located from the access opening?
  • In plumbing, what is the minimum thickness for concrete encasing trench drains?
  • How far above the highest point of usage should a pressure vacuum breaker be installed?
Subscribe

Get the latest from Passetra

You can unsubscribe at any time. Read our privacy policy